Product Photo
Easy Peel Film for Retort Food F45A5 (50μm)
Easy-peel retort lidding film for PP food containers. Withstands pressurized high-temperature sterilization (121–130°C) while keeping peel force stable and consistent, safe and hygienic for direct food contact.
A Purpose-Built Easy-Open Lid for Retort Food
Laminated into a structure such as PET 12μm // AL 9μm // ONY 15μm // EO-RCPP 50μm, F45A5 forms the food-contact heat-seal layer of the lid. Unlike lidding films that lose seal integrity or shift in peel strength after autoclaving, it is formulated to hold a stable heat-sealing tension with only a small, predictable difference in peel force before and after sterilization — giving converters and co-packers a heat-sealing window of over 30°C to work with on the production line.
Where F45A5 Is Used
- 1
Easy-Open Retort Lid Material
Easy-open lid material for retort-sterilized food packaging. F45A5 is the 50μm mid gauge, holding peel force stable and consistent through pressurized sterilization while remaining safe and hygienic for direct food contact.
- 2
High-Temperature Processed Food
High-temperature processed food packaging containers. Withstands 121–130°C pressurized sterilization, with the published test at 121°C for 30 minutes and a heat-seal condition of 3.2 kg/cm² for one second.
- 3
Heat-Seal Layer After Lamination
Heat-seal layer for lid material after lamination. The recommended structure is PET 12μm // AL 9μm // ONY 15μm // EO-RCPP 50μm; the extra 20μm over F4531 gives more sealant to flow across container rim imperfections.
- 4
Sealing to PP Containers
Suitable for PP (polypropylene) packaging containers. Elongation 700/800% and tensile modulus 5600/5400 kg/cm² balance the give needed at the seal with the stiffness needed on the lidding machine.
- 5
Pet Food and Ready Meals
Pet food, canned food, micro (microwaveable) food, and ready-to-eat meals — the volume retail categories where trays are filled, sealed, retorted, and then shipped shelf-stable.
- 6
Consistent Peel Force
A consistent opening experience at the consumer end: peel force stays even across the seal rather than starting tight and releasing suddenly, which is what keeps sauce or broth in the tray when the lid comes off.
Full Specifications — EO-RCPP Easy Peel Film Series
F45A5 is the 50μm grade in Intlpak's EO-RCPP easy peel film family — a 50 micron easy peel retort lidding film for PP food containers, resisting pressurized sterilization from 121°C to 130°C, with 12.9% haze and 700% elongation (MD). The table below shows F45A5 alongside its 30μm and 70μm siblings for reference.
| Property | Standard | Unit | F4531 (30μm) | F45A5 (50μm) | F45A7 (70μm) |
|---|---|---|---|---|---|
| Thickness | — | μm | 30 | 50 | 70 |
| Yield Point (MD) | ASTM D882 | kg/cm² | 240 | 240 | 240 |
| Yield Point (TD) | ASTM D882 | kg/cm² | 220 | 220 | 220 |
| Break Point (MD) | ASTM D882 | kg/cm² | 610 | 550 | 520 |
| Break Point (TD) | ASTM D882 | kg/cm² | 330 | 350 | 420 |
| Elongation (MD) | ASTM D882 | % | 590 | 700 | 770 |
| Elongation (TD) | ASTM D882 | % | 650 | 800 | 830 |
| Tensile Modulus 2% (MD) | ASTM D882 | kg/cm² | 5500 | 5600 | 5600 |
| Tensile Modulus 2% (TD) | ASTM D882 | kg/cm² | 5200 | 5400 | 5500 |
| Static C.O.F. (corona treated) | ASTM D1894 | kg/200g | 0.78 | 0.70 | 0.80 |
| Static C.O.F. (untreated) | ASTM D1894 | kg/200g | 0.21 | 0.27 | 0.26 |
| Kinetic C.O.F. (corona treated) | ASTM D1894 | kg/200g | 0.64 | 0.65 | 0.74 |
| Kinetic C.O.F. (untreated) | ASTM D1894 | kg/200g | 0.19 | 0.25 | 0.25 |
| Haze | ASTM D1003 | % | 8.0 | 12.9 | 13.7 |
| Width | — | — | Customized | ||
| Length | — | — | Customized | ||
| Recommended Structure | PET 12μm // AL 9μm // ONY 15μm // EO-RCPP 50μm | ||||
|---|---|---|---|---|---|
| Heat Seal Condition | Pressure 3.2 kg/cm², Time 1 sec | ||||
| Sterilization Condition (test) | Temperature 121°C, Time 30 min | ||||
Reviewed by: Intlpak R&D Team.
Why Converters Choose F45A5
Storage Notice
Avoid exposure to direct light, wind, and rain — store under appropriate conditions. Prevent products from slipping from high places, being polluted, or being impacted during handling.
Quality & Certification
Manufactured under ISO 9001 quality management and GMP clean-room production, with ISO 22000 & HACCP food-safety certification. All products undergo annual safety checks.
Questions About F45A5
When does F45A5 make more sense than the 30 or 70 μm grades?
When the lid needs more stiffness than F4531 (30 μm) but doesn't justify F45A7 (70 μm), the 50 μm F45A5 is the middle answer. All three share heat rating and laminate structure, so the choice is really rigidity versus unit cost — wider container openings, or packs that see compression in transit, usually start here.
F45A5 is rated 130°C — what conditions was it actually validated at?
The rating is a ceiling; the tested condition is 121°C for 30 minutes under pressurized sterilization. Keep the two apart: 121°C/30 min is the validated retort process, 130°C is what the film structure withstands. If your process runs hotter than 121°C, request samples and validate seals under your real conditions first.
Does F45A5 run the same heat-seal settings as its siblings?
It does. The whole series shares 3.2 kg/cm² pressure for 1 second, with a sealing window likewise above 30°C. A line already running F4531 or F45A7 does not need seal-bar recalibration to switch — only a check on stroke to account for the gauge change.
Once laminated, what does F45A5 seal to?
PP containers, with its sealing face doubling as the food-contact face. The laminate follows the series' standard foil composite layup with a 50 μm inner layer, producing a retortable easy-peel lid for pouched meals, pet food and microwaveable trays. Lines already running F4531 or F45A7 keep the same layer configuration and change only the inner-layer grade.
F45A5 elongates 700%/800% — more than the 30 μm grade. Why does that matter?
Higher elongation means the film yields rather than fractures under load. F45A5 runs 700%/800% MD/TD against F4531 's 590%/650%, so localized stress — transit vibration, or the moment a consumer tears the lid — is absorbed by stretching instead of splitting. The trade-off is slightly lower break point (550 versus 610 kg/cm² MD).
Which lidding film suits ready-meal trays that are sterilized after filling?
One that keeps a consistent peel force before and after retort. F45A5 is the 50 μm EO-RCPP easy-peel grade, resisting pressurized sterilization from 121°C to 130°C with 12.9% haze and 700%/800% elongation. It seals to PP food containers and is laminated with PET, OPP or NY to form the finished lid. Peel behaviour is the point — a lid that seals hard but opens cleanly.
Can a lid survive high-temperature sterilization and still peel cleanly afterwards?
That is the specific job of a retort-grade easy-peel film. Ordinary peelable sealants either weld shut under pressurized heat or lose seal integrity. Intlpak's EO-RCPP grades — F4531 at 30 μm, F45A5 at 50 μm and F45A7 at 70 μm — are built to hold peel force stable before and after 121–130°C retort, so the pack that survives the autoclave still opens by hand.